47 + The Number One Article on Brick Floor Kitchen Farmhouse Style

What sort of deck do you stroll on when inside your kitchen? Is it hardwood? Stone tiles? Brick floor? Marble? The innovative extravagance vinyl flooring? The polyurethane marmoleum flooring? Or on the other hand something more perfect overlaid with costly covers? Whatever floor plans you have introduced in your kitchen or are just going to, you should take a gander at your alternatives first prior to settling on a choice. That is on the grounds that there are many floor types to browse and it’s not simply modest wood flooring or the less difficult looking stone floor. There are even fascinating floors that you presumably never knew about!

While thinking about what material to use for a story, hardly any individuals look past a solid piece, with something like tile or floor covering as a completion. As far as we might be concerned, in any case, there were a few factors that made a balanced out compacted earth Brick (SCEB) floor undeniably really engaging, including cost, ability, and time required.


  • Packed Earth Blocks
  • Screened sand
  • Sealer – acrylic or oil based solid sealer or stain


  • Round saw with brick work edge (discretionary)
  • 2 levels, one little, one longer
  • Elastic hammer
  • 2 sheets to remain on. You would prefer not to remain on the sand as your feet will make enormous scratches. In the event that you remain on a board, your weight is spread out and the smooth surface of the sand isn’t undermined.
  • Careful tape. The individual laying the Brick ought to think about taping their fingertips with careful tape. This secures them without bargaining smoothness.
  • Roller and brush


Get ready and level your sub-floor, adding on the off chance that you wish any fume boundary, warming framework, and protection. Put a 1 inch layer of fine screened sand over the entire zone. Minimized and level the sand. The most straightforward approach to do this is to cover and level a piece of square tubing in the sand on one or the other side of the room, so the highest point of the metal is flush with the level you need the sand to be.

You at that point connect another piece of metal between the 2 bits of square tubing, so it sits on top of them, and drag it in reverse and advances over the zone until it is smooth.

Source : Pinterest

>>>>>>> View Gallery <<<<<<<

Pick your example before you start, and gauge the measure of the floor and Brick you will require. Running bond is regularly the most effortless example to consider going all in, yet none of them are hard. The Herring bone can be hard to picture, however once you get moving, it’s not almost at scary as it appears.


Regardless of which design you choose to utilize, you will require some cut Bricks. Attempt and work out generally the number of you will require for your beginning edge and cut those early. The ones required at the opposite finish of your lines, you can do once the remainder of the floor is laid, cut the brick utilizing a round saw with workmanship edge. On the off chance that you are not very specific about the edges of your cut Bricks, it is far simpler to break them as opposed to cutting.


Spot every Brick, individually, where you need it to go.

With the long level, check it is level with past Brick or existing floor. With the short level, ensure the actual Brick is level every which way. You additionally need to watch that it is fixed up well with the divider.

Utilize the elastic hammer to tap the Brick tight against its neighbors. What’s more, tap down on it to get the level right.

At the point when you get to the far edge of the divider from where you began, and you don’t have a Brick to fit in the space, leave it. You ought to do all the edge Bricks toward the end. Indeed, even before the floor is done, you can stroll on it. Try not to step close to incomplete edges.


For the edges, you may need to gauge each space and slice or break Bricks to fit. Then again, you can fill the holes with an exceptionally fine solid when you do the border.

When you have all the Bricks laid, you can fill the border, in the middle of the Bricks and walls, with concrete. This doesn’t utilize a lot of cement, and should be possible in 30 minutes. Screen your sand and afterward scoop the solid smooth and level with the highest points of the Bricks.


When every one of your Bricks, including your edge Bricks, are set up, clear fine sand into the breaks. Permit the floor to several days, and afterward clear more sand into the breaks. Rehash this multiple times until the sand does not settle anymore.


To seal the Bricks so you can clear and wipe them, utilize an acrylic or oil based solid sealer or stain, at any rate two coats. Until this is done, the Brick will be covered in a fine residue (as you progressively wear them out). This is OK for a porch or outside floor, yet for inside it’s not as adequate.

Utilize a little can as well as brush to trickle sealer altogether the breaks first. Whenever that has set up, utilize a roller to spread the stain on the Brick surface.

The sealer will obscure the characteristic shade of the Bricks. Most solid sealers and stains smell unequivocally. Continuously give satisfactory ventilation, and plan to keep those windows open for a couple of days.


Leave a Reply

Your email address will not be published.